March 2, 2025
 |  390 Comments

‘hola mundo’ means ‘hello world’ in Spanish.

“Bare Metal” is a machine that offers direct access to the hardware, without any abstraction or virtualization layer. This means that the user has full control over the hardware and can install their own operating system, software and settings.

You have to create a program in assembly in real mode.

The following program is assembly for x86_64.

Is an example of a PC-Boot. It is a very basic bootloader that prints the message “Hola Mundo” on the screen.

  • It runs directly without the need for an additional bootloader.
  • It is limited to 512 bytes of code.
  • It is loaded into memory by the BIOS.
  • It does not use GRUB or any other bootloader.
  • It is used on older x86 systems.

A PC-Boot is a type of bootloader used on older x86 systems. It is a very basic bootloader that is loaded into memory by the BIOS and executed directly.

types of bootloaders:

  • PC-Boot
  • Boot Sector Bootloader
  • Direct Boot Bootloader
  • Sector Load Bootloader
  • MBR (Master Boot Record) Bootloader
  • PC Bootstrap Loader
  • Volume Boot Record (VBR) Bootloader
  • Boot Sector Bootloader

PC Bootstrap Loader:
This type of bootloader is the one that is loaded into memory by the BIOS when a computer with a hard drive or solid state drive (SSD) is started.

A bootloader is a program that runs at system startup and is responsible for loading your application into memory.

bootloader.asm

[BITS 16]
[ORG 0x7C00]
mov ax, 0x07C0
mov ds, ax

; Display Settings
mov ah, 0x00
mov al, 0x03
int 0x10

; Printing the message
mov ah, 0x0E
mov al, 'H'
int 0x10
mov ah, 0x0E
mov al, 'o'
int 0x10
mov ah, 0x0E
mov al, 'l'
int 0x10
mov ah, 0x0E
mov al, 'a'
int 0x10
mov ah, 0x0E
mov al, ' '
int 0x10
mov ah, 0x0E
mov al, 'M'
int 0x10
mov ah, 0x0E
mov al, 'u'
int 0x10
mov ah, 0x0E
mov al, 'n'
int 0x10
mov ah, 0x0E
mov al, 'd'
int 0x10
mov ah, 0x0E
mov al, 'o'
int 0x10

jmp $

TIMES 510-($-$$) DB 0
DW 0xAA55

the program:

  • It runs directly without the need for an additional bootloader.
  • It is limited to 512 bytes of code.
  • It does not use GRUB or any other bootloader.
  • It is loaded into memory at address 0x7C00.
  • It sets the video mode to 80×25 text mode.
  • It prints the message “Hello World” on the screen.
  • It runs indefinitely.

what the program does:

  • memory address 0x7C00, which is the address where the BIOS loads the boot sector.
  • addressing mode: The code uses 16-bit addressing mode, as indicated on the first line [BITS 16]. This means that memory addresses are expressed in 16 bits, which limits the amount of memory that can be accessed.
  • Load address: The program load address is 0x7C00, as indicated in the second line [ORG 0x7C00]. This means that the BIOS loads the boot sector at this memory address.
  • Setting the video mode: The mov ah, 0x00 line loads the value 0x00 into the AH register. Then the mov al, 0x03 line loads the value 0x03 into the AL register. Finally, the int 0x10 line calls interrupt 0x10, which is the video interrupt. The value 0x03 in AL sets the video mode to 80×25 text mode.
  • Printing Characters: The following lines print the characters “Hello World” to the screen. Each character is printed using interrupt 0x10, with the value 0x0E in AH and the character to be printed in AL.
  • Infinite loop: The jmp$ line creates an infinite loop, meaning the program will run indefinitely.
  • Byte padding: The TIMES 510-($-$$) DB 0 line pads the remaining bytes of the boot sector with zeros. This is necessary because the boot sector must be exactly 512 bytes long.
  • Boot Mark: DW line 0xAA55 places the boot mark at the end of the boot sector. This mark is required for the BIOS to recognize the boot sector as a valid boot program.

compile and generate .bin:

 nasm -f bin bootloader.asm -o bootloader.bin

create image .img:

dd if=bootloader.bin of=bootloader.img bs=512 count=1

copy to usb:

sudo dd if=bootloader.img of=/dev/sdb bs=4M

my usb is /dev/sdb you can see your device with lsblk, without /dev

sync data:

sudo sync

The following commands show the hexadecimal information of /dev/sdb, the USB and the bootloader.img file:

Information is displayed only in the first 512 bytes, This is because if the USB is, for example, 64 GB, the 64 GB of information will be displayed and not the first 512 bytes.

Check that there is the same information in the bootloader.img file and in /dev/sdb on the USB.

The USB does not have a partition, but instead makes an exact copy per sector on the device, starting from the beginning, the first bytes.

 sudo hexdump -C -n 512 /dev/sdb

hexdump -C -n 512 bootloader.img

demonstration

connect usb to computer:

enter the bios, press ‘delete’ at the beginning to enter

In the BIOS go to the boot section:

Select the USB flash drive first in order of priority:

that is the process of booting a usb.

After starting the computer it shows the message ‘Holundo’

in video:

The message on this computer is incorrect, it should display ‘Hola Mundo’

I’m investigating because it’s incorrect.

Maybe my BIOS is configured incorrectly.

Post Views: 1,034
Tags: , , , , , , ,